Osram-sylvania BoxLED Plus BX06BA-WF4 Bedienungsanleitung PDF herunterladen

BoxLED

Plus BX06BA-WF4

Signage Lighting System

INSTALLATION GUIDE

WARNING: ONLY QUALIFIED PERSONNEL SHOULD PERFORM INSTALLATION

TO AVOID ELECTRICAL SHOCK OR COMPONENT DAMAGE, DISCONNECT POWER BEFORE PERFORMING

INSTALLATION OF THE POWER SUPPLIES, MODULES, AND/OR RGB CONTROLLERS.

Failure to install the power supplies and/or LED modules in accordance with the National Electric Code (NEC), all applicable

Federal, State, and local electric codes as well as the specific Underwriters Laboratories (UL) safety standards for the

installation, location and application may cause serious personal injury, death, property damage and/or product malfunction.

These instructions are guidelines for installation of LED modules and power supplies. Installation requirements may vary

depending on the application. Licensed electricians should provide all installation services for connection for both primary

and secondary (input/output) of the power supplies.

1.0 PREPARE FOR INSTALLATION

1.1 Tools Required:

- Wire stripper/cutter

- Screwdriver

- Measuring tape

1.2 Supplies Required:

- PLTC cable

- Wire nuts/connectors

- #8 screws or rivets

- Accessory Mounting Track

1.3 Carefully remove existing neon or fluorescent tubes, HID or incandescent light

sources and power supplies and/or ballasts if necessary.

1.3.1 Make sure power is turned off.

a. Where applicable, determine if a disconnect switch needs to be

installed (may be integral with existing power supply/transformer).

1.3.2 Remove all existing screws, sockets and wiring.

1.3.3 Dispose of all old sign components in the proper manner.

1.3.4 Repair and seal any unused openings in the sign enclosure. Openings

greater than ½” diameter require a metal patch secured by screws or rivets

and caulked with non-hardening caulk. Smaller openings may be sealed

with non-hardening caulk.

1.3.5 Clean the inside of the sign to make sure it is free of dirt.

LED341

www.sylvania.com/SIGNAGE

1 2 3 4 5

Inhaltsverzeichnis

Seite 1 - Signage Lighting System

BoxLED® Plus BX06BA-WF4 Signage Lighting System INSTALLATION GUIDE WARNING: ONLY QUALIFIED PERSONNEL SHOULD PERFORM INSTALLATION TO AVOID ELECT

Seite 2 - 2.0 MECHANICAL INSTRUCTIONS

2 2.0 MECHANICAL INSTRUCTIONS 2.1 Measure the inside of the frame to determine the length of the mounting tracks (see Figure 1). 2.2 Cut the

Seite 3 - 3.0 ELECTRICAL INSTRUCTIONS

3 2.5 Clean the mounting traks to ensure optimum adhesion of the LED modules. 2.6 Remove the protective film from the tape on the back of the LE

Seite 4

4 3.4 OPTIONAL AC DISCONNECT SWITCH INSTALLATION: Connect disconnect switch in line with VAC line (black wire) (see Figure 13). Figure 3.1

Seite 5 - 4.0 Troubleshooting Guide

5 4.0 Troubleshooting Guide Problem Possible Cause Corrective Action Entire sign does not light No input power Check AC connection to power supp

Kommentare zu diesen Handbüchern

Keine Kommentare

Osram-sylvania BoxLED Plus BX06BA-WF4 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Beleuchtung Osram-sylvania BoxLED Plus BX06BA-WF4 herunter. OSRAM SYLVANIA BoxLED Plus BX06BA-WF4 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Beleuchtung Osram-sylvania BoxLED Plus BX06BA-WF4