Osram-sylvania LEDstixx Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Beleuchtung Osram-sylvania LEDstixx herunter. OSRAM SYLVANIA LEDstixx User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 8
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
1
LEDstixx
®
Lighting System
For Shallow and Deep Set Back Cooler Cases - 3 Series
INSTALLATION GUIDE
WARNING: ONLY QUALIFIED PERSONNEL SHOULD PERFORM INSTALLATION
TO AVOID ELECTRICAL SHOCK OR COMPONENT DAMAGE, DISCONNECT POWER BEFORE ATTEMPTING INSTALLATION OF THE POWER SUPPLIES
AND/OR MODULES.
Failure to install the power supplies and/or LED modules in accordance with the National Electric Code (NEC), all applicable Federal, State and local electric
codes as well as the specific Underwriters Laboratories (UL) safety standards for the installation, location and application may cause serious personal injury,
death, property damage and/or product malfunction.
These instructions are guidelines for installation of LED modules and power supplies. Installation requirements may vary depending on the application. Licensed
electricians should provide all installation services for connection for both primary and secondary (input/output) of the power supplies.
WARNING”: Risk of fire or electric shock. Luminaires, wiring, ballasts, or other electrical parts may be damaged when drilling for installation of reflector kit
hardware. Check for enclosed wiring and components.
WARNING”: Risk of fire or electric shock. Reflector/retrofit kit installation requires knowledge of fluorescent lighting luminaires electrical systems. If not qualified,
do not attempt installation. Contact a qualified electrician.
WARNING”: Risk of fire or electric shock. Install this kit only in luminaires that have the construction features and dimensions shown in the “product diagram”.
WARNING”: To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
Identification and Warnings of Safety Hazards
In accordance with ANSI Z535.4-2002 the following system of identifying the severity of the hazards associated with the products is used:
DANGER”: Imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING”: Potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION”: Potentially hazardous situation which, if not avoided, may result in minor or moderate injury or property damage. Also used to alert against unsafe
practices.
IGNORING A HAZARD WILL VOID ANY WARRANTY
www.osramamericas.com
This installation guide outlines step-by-step instructions for
proper mechanical and electrical installation of OSRAM
LEDstixx® Lighting System products and power supplies. This
document should never be considered a substitute for any
provision of a regulation or state and/or legal code.
LED348
Seitenansicht 0
1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - Lighting System

1 LEDstixx® Lighting System For Shallow and Deep Set Back Cooler Cases - 3 Series INSTALLATION GUIDE WARNING: ONLY QUALIFIED PERSONNEL SHO

Seite 2 - System Wattages

2 1.0 MECHANICAL INSTRUCTIONS 1.1 Tools Required: 1.2 Case Configurations:  Philips and/or Flat Bla

Seite 3 - Figure 2 (Shallow Setback)

3 1.3 Case Identification If the installation is a replacement of an existing fluorescent system, it is recommended that the case manufacturer be

Seite 4 - Figure 2

4 Figure 4 1.4.3 Position connector side of LEDstixx up or down depending on the direction of preferred power routing. Please refer to section 1.5

Seite 5

5 1.5 Power Supply Installation Instructions: 1.5.1 To gain access to the existing ballast, the contact Plate Retainer (Zipper Strip) and Contact

Seite 6

6 1.5.5 Install the new Optotronic OT75 power supply and re-use the previous ballast’s screws to secure the OT75 into the existing mounting holes.

Seite 7 - 2.0 ELECTRICAL INSTRUCTIONS

7 2.0 ELECTRICAL INSTRUCTIONS 2.1 General Instructions: If additional wiring becomes necessary, it is the responsibility of the insta

Seite 8 - 3.0 RELATED INFORMATION

8 Notes: 1. The wiring diagram is purely diagrammatic. The power supply DC output wiring must be kept separate from any AC wiring. Therefore the or

Kommentare zu diesen Handbüchern

Keine Kommentare